A small instrument for your dash#
OpenCarMind EdgeOS turns the ESP-Mosaico into a car computer. It comes from the same source as the OpenCarMind firmware for the ESP32-S3 board and does the same job, on a bigger touch screen with more memory. Up to version 1.2.0 this firmware was called mossREV.
It reads the car#
A Bluetooth LE OBD-II adapter plugs into the car’s diagnostic port. OBD-II is the standard port under the dash. It reports engine speed, road speed, temperatures and trouble codes. The board talks to the adapter over Bluetooth LE.
It logs every drive#
The board saves each drive as its own session on its 128 MB drive store. You copy drives to your computer over the USB cable with the desktop app. Nothing has to come out of the board.
It runs AI on the chip#
A small neural network, called the model, watches the last few seconds of driving. It says what you are doing: stopped, braking, accelerating or cruising. It also estimates brake pressure, engine torque and fuel rate, which most cars do not report.
Note
What 2.1.0 adds
Version 2.1.0 adds a Health app with three pages: the battery, the network guard and the AI services. Three new AI services run on the chip: a state-of-health estimate from your charges, a battery anomaly detector and a network guard for Bluetooth and Wi-Fi. They only watch and warn. The battery detector never touches the power, and the guard never cuts your car link or transmits anything. The 17 apps explains the Health app and Health checks and messages the guard’s messages. These parts are built and checked on a computer and are being checked on the board.
What 2.0.0 added
Version 2.0.0 adds a small operating-system layer. You do not have to set anything up for it. About a minute after every start the board rates its own health and shows it on the Board page. While you drive it refuses changes that could spoil the drive, such as a model switch, and tells you why. It watches the battery’s temperature and voltage. It pairs a new OBD adapter only when you say yes. Health checks and messages explains every line and message it shows.
Note
Local first
The board keeps your drives in its own storage. Wi-Fi is optional and has one job. While the car is parked, it sets the clock from a time server, and then the radio stops. A value the car does not give shows as a dash, never as a made-up figure.
The hardware#
Board: Espressif ESP-Mosaico V1.2
Chip: ESP32-S31, dual core, run at 320 MHz
Memory: 32 MB PSRAM, measured on the board
Flash: 16 MB, for the firmware and the state files
Drive store: 128 MB SPI NAND, for the drive logs
Screen: 2.16 inch AMOLED, 480 x 480, touch
Battery: a 3.7 V, 65 mAh cell with a fuel gauge
Radio: Wi-Fi and Bluetooth. The adapter uses Bluetooth LE.
USB: one USB-C port for power, the desktop app and updates
Words used in this manual#
App: one full screen with its own job, opened from the launcher
Launcher: Home plus four pages of app tiles
Drive: one session, from the car connecting to the drive ending
Model: the on-board AI: CarMind R.E.V or CarMind E.V
Learning: R.E.V correcting its own fuel figures from what your car reports
Board state: what the board is doing right now, such as Parked or Driving. The firmware calls these runlevels.
Health: the board’s own verdict after a start: good, degraded or bad
NAND: the board’s 128 MB drive store
MIL: the check-engine light
DTC: a diagnostic trouble code, such as P0300
Warning
About the captures in this manual.
Most come from an OpenCarMind EdgeOS 2.0.0 board (build 06ddf1d), taken on a bench with no car connected. Eight screens had no clean board capture: Home, Learning with E.V in use, Live, Fuel, Brakes and torque, Trip, Engine and the alarm banner. Those are rendered on a computer from the 2.0.0 screen code with example values, and their captions say so. They are not photos of the board.
The pairing sheet for a new adapter (see Pairing your OBD adapter) has no capture yet.