OBD-II adapters#

OpenCarMind talks to the car through a Bluetooth LE adapter that speaks the ELM327 command set. This page lists the adapters the firmware was written to support, what each one uses on the radio, and where to buy it.

Only the LELink has been driven with this board. Every other row is based on the adapter’s published Bluetooth layout or on what other open-source OBD projects use for it. If you try one, please report the result with the Field check issue template so the table can move from “expected” to “tested”.

What the board needs from an adapter#

  • Bluetooth LE. The ESP32-S3 has no Classic Bluetooth radio, so adapters that only offer Bluetooth 3.0 (SPP) cannot connect. Many cheap adapters sold as “Android only” are Classic.

  • ELM327 or STN commands. Adapters that only work with their own app and speak a private protocol will connect, fail the ELM327 reset, and be skipped.

How the board finds and talks to an adapter#

  1. It scans and collects candidates for 1.5 s, then connects to the one with the strongest signal. A device counts as a candidate when its name contains a word adapters use (OBD, ELM327, Vgate, vLink, Veepeak, Carista, Kiwi, LELink, Konnwei, Viecar and others), when its name starts with an entry of OBD_BLE_NAME_PREFIXES, or when it advertises a service that OBD adapters use (FFF0, 18F0, BEEF, or the Vgate E7810A71 service).

  2. It reads the GATT table and picks the serial line. Known layouts are tried first, then the first non-standard service with a characteristic it can subscribe to (notify or indicate) and one it can write to.

  3. It subscribes. If the adapter refuses because the link is not encrypted, the board pairs with Just Works and bonds. If Just Works is refused, it tries once more with the fixed PIN 123456, which OBDLink documents for its CX.

  4. It sends ATZ. The address is stored only after the device answers like an ELM327. A device that has no serial line, cannot be subscribed to, or never answers is skipped for 10 minutes and the scan moves on.

  5. Writes are cut to the negotiated MTU, and each piece waits for its acknowledgement.

  6. If the ECU does not answer under automatic protocol search, the board tries each protocol in turn (CAN 11-bit 500k, CAN 11-bit 250k, J1850 PWM, CAN 29-bit 500k, CAN 29-bit 250k, J1850 VPW, ISO 9141-2, ISO 14230 slow and fast init).

Known serial layouts#

Layout

Service

Receive

Send

Seen on

Source

FFF0

FFF0

FFF1 (notify)

FFF2 (write)

OBDLink CX, Veepeak, Carista, most clones

OBDLink CX developer notes, Stack Overflow

FFE0

FFE0

FFE1

FFE1 (same characteristic)

LELink, HM-10 style clones

tested on this board

FFE0 split

FFE0

FFE1

FFE2

adapters with the Deep OBD firmware

EdiabasLib BtLeGattSppAndroid.cs

Vgate E7810A71

E7810A71-73AE-499D-8C15-FAA9AEF0C3F2

BEF8D6C9-9C21-4C9E-B632-BD58C1009F9F

same characteristic

Vgate vLinker

EdiabasLib, LTSupportAutomotive, ha-obd-ble

Vgate 18F0

18F0

2AF0

2AF1

Vgate iCar Pro BLE

SwiftOBD2

BEEF

BEEF

picked by property

picked by property

listed by LTSupportAutomotive

LTSupportAutomotive

Nordic UART

6E400001-B5A3-F393-E0A9-E50E24DCCA9E

6E400003

6E400002

some DIY and clone adapters

AndrOBD

Adapters#

Prices are in US dollars, taken from US listings seen on 3 November 2026 and change often. “Not found” means no current price showed up. Amazon links are plain product pages with no affiliate tag. Each one was opened on 3 November 2026 and showed the named product. Where the title does not name the model or the page showed the item unavailable, the Status column says so.

Adapter

Radio

Layout

Status

Price seen

Buy

LELink²

BLE

FFE0

Tested on this board

not found

Amazon B0755N61PW, original LELink B00QJRYMFC

Veepeak OBDCheck BLE+

BLE (Classic too, for Android)

FFF0

Expected

about 38 to 42 USD at US retailers

Amazon B076XVQMVS

Veepeak OBDCheck BLE

BLE 4.0

FFF0

Expected

about 32 USD at a US retailer

Amazon B073XKQQQW

OBDLink CX (Amazon lists it as the Bimmercode edition, the only CX model)

BLE 5.1

FFF0, always encrypted

Expected, pairs on demand. Bonding is open for the first 5 minutes after the adapter powers up

79.95 USD

Amazon B08NFLL3NT

Vgate iCar Pro BLE 4.0

BLE, shows up as IOS-Vlink

18F0

Expected

31.49 USD

Amazon B06XGB4873

Vgate vLinker MC+

BLE and Classic, BLE side named vLinker MC-IOS

Vgate E7810A71 or generic

Expected

about 55 USD

Amazon B088LW211V

Vgate vLinker FS

Classic and BLE, ships in MFi mode

Vgate E7810A71 or generic

Needs a setting: switch it to “BLE+BT” with the VgateFwUpdater app first

not found

Amazon B0BZTXV6MZ

Vgate vLinker MS

Classic and BLE, ships in MFi mode

Vgate E7810A71 or generic

Needs a setting: switch it to “BLE+BT” with the VgateFwUpdater app first

not found

Amazon B0D6YQX4R8

Carista OBD2 / Carista EVO

BLE

FFF0

Expected

not found

Amazon B00YVHGTBM, EVO B0CM9W4MCW

FIXD

Bluetooth

unknown

Unverified. One owner reports it works with other ELM327 apps

not found, first generation discontinued

Amazon B013RIQMEO

Generic “ELM327 BLE 4.0” clones

BLE

usually FFF0 or FFE0

Expected for most. Some fake v2.1 clones skip commands

varies

example: RODEDIO B0GWQKLTMR, whose listing says Bluetooth LE on iOS

Panlong PL-B04

Bluetooth, iOS and Android

generic

Expected for the “For iOS Android” option: that listing says it works with Car Scanner on iOS, which needs BLE and ELM327. The “For Android Only” option is likely Classic. The page title does not name the model

not found

Amazon B0C1GDJ9ZJ

DA200 (sold as “OBD2 Scanner Bluetooth 5.4 with AI Repair Tips”)

BLE 4.0 / 5.4

generic

Expected: the maker’s spec sheet lists BLE, a PIC18F25K80 main chip (the chip most ELM327 v1.5 clones use) and all 9 OBD-II protocols. The Amazon title does not name the model, so check for DA200 on the box

not found

Amazon B0FH2GJTP8

V800 full-system scanners (Panlong PL-V800, white-label copies such as VQQEFF)

Bluetooth

private app

Not expected: the Panlong listing says it uses the INNOOBD+ app and does not support third-party apps. Its title says “Engine Transmission ABS SRS” and does not say V800

not found

Amazon B0GQ3D57PK

“OBD2 Scanner AI Diagnostic Tool” with an exclusive app

Bluetooth

unknown

Unverified: the listing names no chip, no Bluetooth type and no third-party apps

not found

Amazon B0H3F4WYXN

BlueDriver Bluetooth Pro

Bluetooth

private protocol

Not expected: reported to work only with its own app

79.95 USD

Amazon B00652G4TS

OBDLink MX+

Classic Bluetooth 3.0

SPP

Will not work, no Classic radio on the S3

139.95 USD

Amazon B07JFRFJG6

OBDLink LX

Classic Bluetooth 3.0

SPP

Will not work, no Classic radio on the S3

not found

Amazon B00H9S71LW

KONNWEI KW902

Classic, listed for Android and Windows only

SPP

Will not work, no Classic radio on the S3. Listing showed “currently unavailable” on 3 Nov 2026

not found

Amazon B073F57QT3

Not listed? Check your adapter with a BLE scanner app such as nRF Connect. A service with one characteristic that notifies or indicates and one you can write is enough for the generic fallback. When the name has none of the words above and the adapter advertises no known service, add its name to OBD_BLE_NAME_PREFIXES in idf.py menuconfig.

Sources for the adapter facts#